War Doctor: Finally...almost

One more publicity shot (the last) of John Hurt as the Doctor

Lot's of good progress this weekend. I've completed all of the major components and am down to the final punch list. Here's what I've complete so far.

The shirt dyed grey

The amazing leather waistcoat found at Goodwill for $3

First off, there's been a last minute change to the waistcoat. Because of the dye problem, I had switched the material I planned on using to some wool I had left over from the Headless Horseman coat. I died it with brown to make a darker red/brown color. I already cut the material and started sewing it together when Harriet found an amazing leather vest at the local Goodwill Store ($3!). It fits perfectly and looks wonderfully weathered. The only problem is that it's not double breasted. However, due to time constraints, I'm going to use it for the initial costume and put off working on the waistcoat until later.

I did decide to dye the shirt grey. The whites were too bright, and the grey gave it a dingy look. I tried staining the shirt with tea and coffee but it just wasn't getting there. After wearing it a few times it will get properly sweaty and worn in.

Coloring the wig with FW ink using an airbrush

I wanted to make sure the roots showed the grey

I finally got to dying the wig. I'm using FW ink, specifically the Cool Grey. I diluted it for the airbrush, approximately 2:1 water to dye. It was all pretty loose measurements, basically putting ink into the airbrush cup with the eyedropper and adding a splash of water before swirling around to mix. That gave me a pretty good density of pigment so I had some subtle control over the color. I particularly focused on getting the pigment into the roots in order to leave some of the blond coloring. I think it went extremely well. After it all dried, I rinsed the wig in cold water which lightened things up a bit more. After drying, I combed the wig quite a bit in order to break up any stiffness left by the dye. I'm pleased with the results (shown later) and all I have left is to style it with got2b. I want to reduce "blow out" look and make it appear more sweaty/greasy.

Tying the shields down to the bandoleer pockets.

The finished bandoleer holding the sonic screwdriver

I spent some time weathering the bandoleer and the leather shields. I did them separately so I could get access to all the hidden bits. I don't have pictures, unfortunately, but I used a wood rasp and a cheese grater to get some of the rough wear. I also took the bandoleer out into our driveway and beat it on the asphalt as well as drag it around our dried out garden beds (California drought). It got nicely gouged and dinged as well as dusty. The shields got a couple of layers of paint, brown and black, before the wood rasp scraped through them, and that added a lot to the ageing (you can see it in the first picture, above). Then I tied the shields onto the bandoleer, glued down the knots, and it's now done-done (that's a technical term that means it doesn't need any more work, as oppose to "done", which means the main construction is complete, but it still needs some finishing).

The half gaiters complete with boot straps. I'll try to dull the red coloration and weather them quite a bit.

To finish the gaiters I added the strap and buckle that goes under the boot. I had to hand stitch the strap to the buckle, but the rest of the straps were machine sewn. I also used the leather punch to make the holes for the buckle.

And that completes the initial work on the costume, so time to give it a try. Here's the first fitting:

Initial complete costume fitting.

I'm very happy with this fitting. It's got the overall look I'm after and the sizes look right. I've got a 13 item punch list for immediate improvements:

  • Change the color of the gaiters: they're too bright red and need weathering
  • Style the wig: the hair should look greasier, like he's worn out not windblown
  • Add a pocket watch chain
  • Add another button on the left gaiter: I left off several button to look like they'd been ripped off in use, but now the gaiter just looks floppy compared to the other side.
  • Remove the coat belt
  • Condition the coat: it has the proper amount of weathering, but now I want to preserve its look, so I'll add leather conditioner/protection.
  • Darken the buttons on the vest: too bright, too bright!
  • Tie the belt tongue down: the belt matches the length shown in the pictures, but right now the tongue flops away from my body. I need a hidden attachment at the end (Velcro?)
  • Weather the pants: too neat
  • Weather the boots: too shiny
  • Loosen the bandoleer shield that holds the sonic screwdriver: it's too difficult to get the screwdriver in and out of the bandoleer.
  • Shorten the coat: It's too long for the pictures, but I don't want to cut the coat
  • Makeup: I need to lighten my mustache and eyebrows. I'd also like to change the ends of the eyebrows to turn up.

These are in order of priority, so I'll get through what I can before C4.

War Doctor: Progress so far

Another publicity shot of John Hurt as the War Doctor

Sorry, it's been awhile since I've had a chance to post my progress. I've received some purchased pieces, and I've made progress on the parts I'm making. Nothing's completed, but lots of significant progress. 

Margnum Classic work boots

That crazy triple hole belt - the right size this time

A replica scarf

The War Doctor's sonic screwdriver

First, the boots arrived. They're Magnum Classics, a version of the work boot that most whovian costumers agree is what's being worn in the show. They were on a clearance sale at the Magnum site.

I also received a replica of the scarf worn by the War Doctor. And I found a set of instructions for tying scarfs, including the "twice around" which is how the doctor appears to wear his scarf.

The belt  I originally receive was too small, and I thought I'd modify it. But I realized there was plenty of time to exchange it for the right sized belt, and it just arrived.

Finally, I bought the toy version of the Doctor's sonic screwdriver. It's a very good replica and will serve me in the short term, but i do plan on making a better prop replica in the future.

A bright red velvet that's suppose to be cotton

I tried dying s small swatch of the fabric in order to establish the right color ratio

To make the waistcoat, I purchase what I thought was cotton velvet. I bought it in a red color and planned on dying it to a darker, bronze color. Well, I tried dying a swatch in order to get the color right but discovered that it wouldn't take the color. I got suspicious that the fabric wasn't cotton, so I decided to try a fabric burn test.

From upper left clockwise: leather, cotton linen, wool, red velvet

The leather barely burned, the cotton linen burned up completely, the wool smelled like burning hair, and the velvet burned into a shiny glob of plastic.

I'd never done the burn test before, so you can see in  the photo that I burned several fabrics at the same time to see how they all behave. I tried a piece of cotton linen, a piece of wool, a bit of leather, and the suspect velvet. The cotton completely burned up with sharp edges left at the unburned fabric. The leather wouldn't burn at all. The wool burned very slowly and smelled like burning hair. And the velvet burned quickly but it burned into a shiny black ball of goo. That was clearly synthetic (plastic) and so to dye it I'll need to use a completely different chemical and process.

Completed sewing the left gaiter

Test fit over the work boot looks good

Both gaiters completed with buttons and button holes

The other side, showing the buttons, but still missing the buckle and belt under the boot

I made some progress with the gaiters. I finished sewing up the two pieces and added the buttons. In the show, several of the buttons are missing, so I tried to match the pattern shown in my close up references. I did a rough fit with the Magnum boot and it looks pretty good. The only things left are to attach the bottom strap and buckle and to weather the pieces.

Soft leather cut to shape.

Pieces of thin styrene cut smaller than the leather

The styrene is heated to mold against a gentle curve

Corners of the laminated shield are cut off

The leather punch used to make the strap holes

The leather is glued to the styrene

A clearer view of the leather/styrene laminate

The cut corners are sanded into a curve

Finally, I started making the small leather shields that sit over the bullet pockets on the bandoleer. I settled on black leather glued down to a thin piece of shaped styrene. For some reason, I took a lot of progress shots so the build is shown in the photo sequence. I still have to paint the styrene, attach the shields to the bandoleer, and then weather.

That's it for the progress so far. Here are the instructions on ways to tie a scarf.

Different ways to tie a scarf